sl-firmware
9ed678ca35
Issue #680 — IMU mount angle calibration: - imu_cal_flash.h/.c: store pitch/roll offsets in flash sector 7 (0x0807FF00, 64 bytes; preserves PID records across sector erase) - mpu6000_set_mount_offset(): subtracts offsets from pitch/roll output - mpu6000_has_mount_offset(): reports cal_status=2 to Orin - 'O' CDC command: capture current pitch/roll → save to flash → ACK JSON - Load offsets on boot; report in printf log CAN telemetry correction (Tee: production has no USB to Orin): - FC_IMU (0x402): pitch/roll/yaw/cal_status/balance_state at 50 Hz - orin_can_broadcast_imu() rate-limited to ORIN_IMU_TLM_HZ (50 Hz) - FC_BARO (0x403): pressure_pa/temp_x10/alt_cm at 1 Hz (Issue #672) - orin_can_broadcast_baro() rate-limited to ORIN_BARO_TLM_HZ (1 Hz) Issue #685 — LED CAN override: - ORIN_CAN_ID_LED_CMD (0x304): pattern/brightness/duration_ms from Orin - orin_can_led_override volatile state + orin_can_led_updated flag - main.c: apply pattern to LED state machine on each LED_CMD received Orin side: - saltybot_can_node.py: production SocketCAN bridge — reads 0x400-0x403, publishes /saltybot/imu, /saltybot/balance_state, /saltybot/barometer; subscribes /cmd_vel → 0x301 DRIVE; /saltybot/leds → 0x304 LED_CMD; sends 0x300 HEARTBEAT at 5 Hz; sends 0x303 ESTOP on shutdown - setup.py: register saltybot_can_node entry point + uart_bridge launch Fix: re-apply --defsym __stack_end=_estack-0x1000 linker fix to branch Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Jetson Nano — AI/SLAM Platform Setup
Self-balancing robot: Jetson Nano dev environment for ROS2 Humble + SLAM stack.
Stack
| Component | Version / Part |
|---|---|
| Platform | Jetson Nano 4GB |
| JetPack | 4.6 (L4T R32.6.1, CUDA 10.2) |
| ROS2 | Humble Hawksbill |
| DDS | CycloneDDS |
| SLAM | slam_toolbox |
| Nav | Nav2 |
| Depth camera | Intel RealSense D435i |
| LiDAR | RPLIDAR A1M8 |
| MCU bridge | STM32F722 (USB CDC @ 921600) |
Quick Start
# 1. Host setup (once, on fresh JetPack 4.6)
sudo bash scripts/setup-jetson.sh
# 2. Build Docker image
bash scripts/build-and-run.sh build
# 3. Start full stack
bash scripts/build-and-run.sh up
# 4. Open ROS2 shell
bash scripts/build-and-run.sh shell
Docs
docs/pinout.md— GPIO/I2C/UART pinout for all peripheralsdocs/power-budget.md— 10W power envelope analysis
Files
jetson/
├── Dockerfile # L4T base + ROS2 Humble + SLAM packages
├── docker-compose.yml # Multi-service stack (ROS2, RPLIDAR, D435i, STM32)
├── README.md # This file
├── docs/
│ ├── pinout.md # GPIO/I2C/UART pinout reference
│ └── power-budget.md # Power budget analysis (10W envelope)
└── scripts/
├── entrypoint.sh # Docker container entrypoint
├── setup-jetson.sh # Host setup (udev, Docker, nvpmodel)
└── build-and-run.sh # Build/run helper
Power Budget (Summary)
| Scenario | Total |
|---|---|
| Idle | 2.9W |
| Nominal (SLAM active) | ~10.2W |
| Peak | 15.4W |
Target: 10W (MAXN nvpmodel). Use RPLIDAR standby + 640p D435i for compliance.
See docs/power-budget.md for full analysis.