246 lines
12 KiB
Markdown
246 lines
12 KiB
Markdown
# SaltyLab Wiring Diagram
|
||
|
||
## System Overview
|
||
|
||
```
|
||
┌─────────────────────────────────────────────────────────────────────┐
|
||
│ ORIN NANO SUPER │
|
||
│ (Top Plate — 25W) │
|
||
│ │
|
||
│ USB-C ──── STM32 CDC (/dev/stm32-bridge, 921600 baud) │
|
||
│ USB-A1 ─── RealSense D435i (USB 3.1) │
|
||
│ USB-A2 ─── RPLIDAR A1M8 (via CP2102 adapter, 115200) │
|
||
│ USB-C* ─── SIM7600A 4G/LTE modem (ttyUSB0-2, AT cmds + PPP) │
|
||
│ CSI-A ──── ArduCam adapter → 2× IMX219 (front + left) │
|
||
│ CSI-B ──── ArduCam adapter → 2× IMX219 (rear + right) │
|
||
│ M.2 ───── 1TB NVMe SSD │
|
||
│ 40-pin ─── ReSpeaker 2-Mic HAT (I2S + I2C, WM8960 codec) │
|
||
│ Pin 8 ──┐ │
|
||
│ Pin 10 ─┤ UART fallback to FC (ttyTHS0, 921600) │
|
||
│ Pin 6 ──┘ GND │
|
||
│ │
|
||
└─────────────────────────────────────────────────────────────────────┘
|
||
│ USB-C (data only) │ UART fallback (3 wires)
|
||
│ 921600 baud │ 921600 baud, 3.3V
|
||
▼ ▼
|
||
┌─────────────────────────────────────────────────────────────────────┐
|
||
│ MAMBA F722S (FC) │
|
||
│ (Middle Plate — foam mounted) │
|
||
│ │
|
||
│ USB-C ──── Orin (CDC serial, primary link) │
|
||
│ │
|
||
│ USART2 (PA2=TX, PA3=RX) ──── Hoverboard ESC (26400 baud) │
|
||
│ UART4 (PA0=TX, PA1=RX) ──── ELRS RX (CRSF, 420000 baud) │
|
||
│ USART6 (PC6=TX, PC7=RX) ──── Orin UART fallback │
|
||
│ UART5 (PC12=TX, PD2=RX) ─── Debug (optional) │
|
||
│ │
|
||
│ SPI1 ─── MPU6000 IMU (on-board, CW270) │
|
||
│ I2C1 ─── BMP280 baro (on-board, disabled) │
|
||
│ ADC ──── Battery voltage (PC1) + Current (PC3) │
|
||
│ PB3 ──── WS2812B LED strip │
|
||
│ PB2 ──── Buzzer │
|
||
│ │
|
||
└─────────────────────────────────────────────────────────────────────┘
|
||
│ USART2 │ UART4
|
||
│ PA2=TX → ESC RX │ PA0=TX → ELRS TX
|
||
│ PA3=RX ← ESC TX │ PA1=RX ← ELRS RX
|
||
│ GND ─── GND │ GND ─── GND
|
||
▼ ▼
|
||
┌────────────────────────┐ ┌──────────────────────────┐
|
||
│ HOVERBOARD ESC │ │ ELRS 2.4GHz RX │
|
||
│ (Bottom Plate) │ │ (beside FC) │
|
||
│ │ │ │
|
||
│ 2× BLDC hub motors │ │ CRSF protocol │
|
||
│ 26400 baud UART │ │ 420000 baud │
|
||
│ Frame: [0xABCD] │ │ BetaFPV 1W TX → RX │
|
||
│ [steer][speed][csum] │ │ CH3=speed CH4=steer │
|
||
│ │ │ CH5=arm CH6=mode │
|
||
└────────────────────────┘ └──────────────────────────┘
|
||
│
|
||
┌────┴────┐
|
||
▼ ▼
|
||
🛞 LEFT RIGHT 🛞
|
||
MOTOR MOTOR
|
||
|
||
|
||
## Wire-by-Wire Connections
|
||
|
||
### 1. Orin ↔ FC (Primary: USB CDC)
|
||
|
||
| From | To | Wire Color | Notes |
|
||
|------|----|-----------|-------|
|
||
| Orin USB-C port | FC USB-C port | USB cable | Data only, FC powered from 5V bus |
|
||
|
||
- Device: `/dev/ttyACM0` → symlink `/dev/stm32-bridge`
|
||
- Baud: 921600, 8N1
|
||
- Protocol: JSON telemetry (FC→Orin), ASCII commands (Orin→FC)
|
||
|
||
### 2. Orin ↔ FC (Fallback: Hardware UART)
|
||
|
||
| Orin Pin | Signal | FC Pin | FC Signal |
|
||
|----------|--------|--------|-----------|
|
||
| Pin 8 | TXD0 | PC7 | USART6 RX |
|
||
| Pin 10 | RXD0 | PC6 | USART6 TX |
|
||
| Pin 6 | GND | GND | GND |
|
||
|
||
- Jetson device: `/dev/ttyTHS0`
|
||
- Baud: 921600, 8N1
|
||
- Voltage: 3.3V both sides (no level shifter needed)
|
||
- **Cross-connect:** Orin TX → FC RX, Orin RX ← FC TX
|
||
|
||
### 3. FC ↔ Hoverboard ESC
|
||
|
||
| FC Pin | Signal | ESC Pin | Notes |
|
||
|--------|--------|---------|-------|
|
||
| PA2 | USART2 TX | RX | FC sends speed/steer commands |
|
||
| PA3 | USART2 RX | TX | ESC sends feedback (optional) |
|
||
| GND | GND | GND | Common ground |
|
||
|
||
- Baud: 26400, 8N1
|
||
- Protocol: Binary frame — `[0xABCD][steer:int16][speed:int16][checksum:uint16]`
|
||
- Speed range: -1000 to +1000
|
||
- **Keep wires short and twisted** (EMI from ESC)
|
||
|
||
### 4. FC ↔ ELRS Receiver
|
||
|
||
| FC Pin | Signal | ELRS Pin | Notes |
|
||
|--------|--------|----------|-------|
|
||
| PA0 | UART4 TX | RX | Telemetry to TX (optional) |
|
||
| PA1 | UART4 RX | TX | CRSF frames from RX |
|
||
| GND | GND | GND | Common ground |
|
||
| 5V | — | VCC | Power ELRS from 5V bus |
|
||
|
||
- Baud: 420000 (CRSF protocol)
|
||
- Failsafe: disarm after 300ms without frame
|
||
|
||
### 5. Power Distribution
|
||
|
||
```
|
||
BATTERY (36V) ──┬── Hoverboard ESC (36V direct)
|
||
│
|
||
├── 5V BEC/regulator ──┬── Orin (USB-C PD or barrel jack)
|
||
│ ├── FC (via USB or 5V pad)
|
||
│ ├── ELRS RX (5V)
|
||
│ ├── WS2812B LEDs (5V)
|
||
│ └── RPLIDAR (5V via USB)
|
||
│
|
||
└── Battery monitor ──── FC ADC (PC1=voltage, PC3=current)
|
||
```
|
||
|
||
### 6. Sensors on Orin (USB/CSI)
|
||
|
||
| Device | Interface | Orin Port | Device Node |
|
||
|--------|-----------|-----------|-------------|
|
||
| RealSense D435i | USB 3.1 | USB-A (blue) | `/dev/bus/usb/...` |
|
||
| RPLIDAR A1M8 | USB-UART | USB-A | `/dev/rplidar` |
|
||
| IMX219 front+left | MIPI CSI-2 | CSI-A (J5) | `/dev/video0,2` |
|
||
| IMX219 rear+right | MIPI CSI-2 | CSI-B (J8) | `/dev/video4,6` |
|
||
| 1TB NVMe | PCIe Gen3 ×4 | M.2 Key M | `/dev/nvme0n1` |
|
||
|
||
|
||
## FC UART Summary (MAMBA F722S)
|
||
|
||
| UART | Pins | Baud | Assignment | Notes |
|
||
|------|------|------|------------|-------|
|
||
| USART1 | PB6=TX, PB7=RX | — | SmartAudio/VTX | Unused in SaltyLab |
|
||
| USART2 | PA2=TX, PA3=RX | 26400 | Hoverboard ESC | Binary motor commands |
|
||
| USART3 | PB10=TX, PB11=RX | — | Available | Was SBUS default |
|
||
| UART4 | PA0=TX, PA1=RX | 420000 | ELRS RX (CRSF) | RC control |
|
||
| UART5 | PC12=TX, PD2=RX | 115200 | Debug serial | Optional |
|
||
| USART6 | PC6=TX, PC7=RX | 921600 | Jetson UART | Fallback link |
|
||
| USB CDC | USB-C | 921600 | Jetson primary | `/dev/stm32-bridge` |
|
||
|
||
|
||
### 7. ReSpeaker 2-Mic HAT (on Orin 40-pin header)
|
||
|
||
| Orin Pin | Signal | Function |
|
||
|----------|--------|----------|
|
||
| Pin 12 (GPIO 18) | I2S BCLK | Audio bit clock |
|
||
| Pin 35 (GPIO 19) | I2S LRCLK | Audio left/right clock |
|
||
| Pin 38 (GPIO 20) | I2S DIN | Audio data in (from mics) |
|
||
| Pin 40 (GPIO 21) | I2S DOUT | Audio data out (to speaker) |
|
||
| Pin 3 (GPIO 2) | I2C SDA | WM8960 codec control (i2c-7) |
|
||
| Pin 5 (GPIO 3) | I2C SCL | WM8960 codec control (i2c-7) |
|
||
| Pin 32 (GPIO 12) | GPIO | Button input |
|
||
| Pin 11 (GPIO 17) | GPIO | RGB LED (APA102 data) |
|
||
| Pin 2, 4 | 5V | Power |
|
||
| Pin 6, 9 | GND | Ground |
|
||
|
||
- **Codec:** Wolfson WM8960 (I2C addr 0x1A)
|
||
- **Mics:** 2× MEMS (left + right) — basic stereo / sound localization
|
||
- **Speaker:** 3W class-D amp output (JST connector)
|
||
- **Headset:** 3.5mm TRRS jack
|
||
- **Requires:** WM8960 device tree overlay for Jetson (community port)
|
||
- **Use:** Voice commands (faster-whisper), wake word (openWakeWord), audio feedback, status announcements
|
||
|
||
### 8. SIM7600A 4G/LTE HAT (via USB)
|
||
|
||
| Connection | Detail |
|
||
|-----------|--------|
|
||
| Interface | USB (micro-B on HAT → USB-A/C on Orin) |
|
||
| Device nodes | `/dev/ttyUSB0` (AT), `/dev/ttyUSB1` (PPP/data), `/dev/ttyUSB2` (GPS NMEA) |
|
||
| Power | 5V from USB or separate 5V supply (peak 2A during TX) |
|
||
| SIM | Nano-SIM slot on HAT |
|
||
| Antenna | 4G LTE + GPS/GNSS (external SMA antennas — mount high on chassis) |
|
||
|
||
- **Data:** PPP or QMI for internet connectivity
|
||
- **GPS/GNSS:** Built-in receiver, NMEA sentences on ttyUSB2 — outdoor positioning
|
||
- **AT commands:** `AT+CGPS=1` (enable GPS), `AT+CGPSINFO` (get fix)
|
||
- **Connected via USB** (not 40-pin) — avoids UART conflict with FC fallback, flexible antenna placement
|
||
- **Use:** Remote telemetry, 4G connectivity outdoors, GPS positioning, remote SSH/control
|
||
|
||
### 9. Power Budget (USB)
|
||
|
||
| Device | Interface | Power Draw |
|
||
|--------|-----------|------------|
|
||
| STM32 FC (CDC) | USB-C | ~0.5W (data only, FC on 5V bus) |
|
||
| RealSense D435i | USB-A | ~1.5W (3.5W peak) |
|
||
| RPLIDAR A1M8 | USB-A | ~2.6W (motor on) |
|
||
| SIM7600A | USB | ~1W idle, 3W TX peak |
|
||
| ReSpeaker HAT | 40-pin | ~0.5W |
|
||
| **Total USB** | | **~6W typical, ~10W peak** |
|
||
|
||
Orin Nano Super delivers up to 25W — USB peripherals are well within budget.
|
||
|
||
---
|
||
|
||
## Data Flow
|
||
|
||
```
|
||
┌──────────────┐
|
||
│ ELRS TX │ (in your hand)
|
||
│ (2.4GHz) │
|
||
└──────┬───────┘
|
||
│ radio
|
||
┌──────▼───────┐
|
||
│ ELRS RX │ CRSF 420kbaud
|
||
└──────┬───────┘
|
||
│ UART4
|
||
┌────────────▼────────────┐
|
||
│ MAMBA F722S │
|
||
│ │
|
||
│ MPU6000 → Balance PID │
|
||
│ CRSF → Mode Manager │
|
||
│ Safety Monitor │
|
||
│ │
|
||
└──┬──────────┬───────────┘
|
||
USART2 ─────┘ └───── USB CDC / USART6
|
||
26400 baud 921600 baud
|
||
│ │
|
||
▼ ▼
|
||
┌────────────────┐ ┌───────────────────┐
|
||
│ Hoverboard ESC │ │ Orin Nano Super │
|
||
│ │ │ │
|
||
│ L motor R motor│ │ SLAM / Nav2 / AI │
|
||
│ 🛞 🛞 │ │ Person following │
|
||
└────────────────┘ │ Voice commands │
|
||
│ 4G telemetry │
|
||
└──┬──────────┬───────┘
|
||
│ │
|
||
┌──────────▼─┐ ┌────▼──────────┐
|
||
│ ReSpeaker │ │ SIM7600A │
|
||
│ 2-Mic HAT │ │ 4G/LTE + GPS │
|
||
│ 🎤 🔊 │ │ 📡 🛰️ │
|
||
└────────────┘ └───────────────┘
|
||
```
|