Implements STM32F722 driver for brushless cooling fan on PA9 using TIM1_CH2 PWM.
Features:
- Temperature-based speed curve: off <40°C, 30% at 50°C, 100% at 70°C
- Smooth speed ramp transitions with configurable rate (default 0.05%/ms)
- Linear interpolation between curve points
- PWM duty cycle control (0-100%)
- State transitions and edge case handling
All 51 unit tests passing:
- Temperature curve verification (6 test zones)
- Speed boundaries and transitions
- Ramp timing and rate control
- PWM duty cycle calculation
- Temperature extremes and boundary conditions
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
Implements complete I2C1 driver for TI INA219 power monitoring IC supporting:
- Dual sensors on I2C1 (left motor @ 0x40, right motor @ 0x41)
- Auto-calibration for 5A max current, 0.1Ω shunt resistance
- Current LSB: 153µA, Power LSB: 3060µW (20× current LSB)
- Bus voltage: 0-26V @ 4mV/LSB (13-bit, 4mV resolution)
- Shunt voltage: ±327mV @ 10µV/LSB (signed 16-bit)
- Calibration register computation for arbitrary max current/shunt values
- Efficient single/batch read functions (voltage, current, power)
- Alert threshold configuration for overcurrent protection
- Full test suite: 12 passing unit tests covering calibration, conversions, edge cases
Integration:
- ina219_init() called after i2c1_init() in main startup sequence
- Ready for motor power monitoring and thermal protection logic
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
Implements TIM4 PWM driver for 2-servo camera mount with:
- 50 Hz PWM frequency (standard servo control)
- CH1 (PB6) pan servo, CH2 (PB7) tilt servo
- 0-180° angle range → 500-2500 µs pulse width mapping
- Non-blocking servo_set_angle() for immediate positioning
- servo_sweep() for smooth pan-tilt animation (linear interpolation)
- Independent sweep control per servo (pan and tilt move simultaneously)
- 15 comprehensive unit tests covering all scenarios
Integration:
- servo_init() called at startup after power_mgmt_init()
- servo_tick(now_ms) called every 1ms in main loop
- Ready for camera/gimbal control automation
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
Adds STM32F7 STOP-mode power management with <10ms wake latency:
- power_mgmt.c: state machine (ACTIVE→SLEEP_PENDING→SLEEPING→WAKING),
30s idle timeout (PM_IDLE_TIMEOUT_MS), 3s LED fade before STOP,
gate SPI3/I2S3+SPI2+USART6+UART5 on sleep (clock-only, state preserved),
EXTI1(PA1/CRSF)+EXTI7(PB7/JLink)+EXTI4(PC4/IMU) wake sources,
PLL restore after STOP (PLLM=8/N=216/P=2 → 216MHz), uwTick save/restore
- Peripheral gating: I2S3, SPI2(OSD), USART6, UART5 disabled during STOP;
SPI1(IMU), UART4(CRSF), USART1(JLink), I2C1 remain active as wake sources
- Sleep LED: triangle-wave pulse (2s period) on LED1 during SLEEP_PENDING,
software PWM in main loop (1-bit, pm_pwm_phase vs brightness)
- IWDG: fed just before WFI; <10ms wake << 50ms WATCHDOG_TIMEOUT_MS
- JLink: JLINK_CMD_SLEEP=0x09, JLINK_TLM_POWER=0x81 (11-byte power frame
at 1Hz: power_state, est_total_ma, est_audio_ma, est_osd_ma, idle_ms)
- main.c: power_mgmt_init(), activity() on CRSF/JLink/armed, tick() when
disarmed, sleep_req handler, LED PWM, JLINK_TLM_POWER telemetry
- config.h: PM_* constants, PM_CURRENT_*_MA estimates, PM_TLM_HZ
- test_power_mgmt.py: 72 tests passing (state machine, LED, gating,
current estimates, JLink protocol, wake latency, hardware constants)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
