Extends the bd-66hx serial protocol with two new Orin→ESP32 commands:
CMD_OTA_CHECK (0x10): triggers gitea_ota_check_now(), responds with
TELEM_VERSION_INFO (0x84) for Balance and IO (current + available ver).
CMD_OTA_UPDATE (0x11): uint8 target (0=balance, 1=io, 2=both) — triggers
uart_ota_trigger() for IO or ota_self_trigger() for Balance.
NACK with ERR_OTA_BUSY or ERR_OTA_NO_UPDATE on failure.
New telemetry: TELEM_OTA_STATUS (0x83, target+state+progress+err),
TELEM_VERSION_INFO (0x84, target+current[16]+available[16]).
Wires OTA stack into app_main: ota_self_health_check on boot,
gitea_ota_init + ota_display_init after peripherals ready.
CMakeLists updated with all OTA component dependencies.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds ota_display_task (5 Hz) on GC9A01 240×240 round LCD:
- Idle: orange dot badge at top-right when update available, version text
- Progress: arc sweeping 0→360° around display perimeter with phase label
- States: Downloading/Verifying/Applying/Rebooting (Balance) and
Downloading/Sending/Done (IO via UART)
- Error: red arc + "FAILED RETRY?" prompt
Display primitives (fill_rect, draw_string, draw_arc) are stubs called
from the GC9A01 SPI driver layer (separate driver bead).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Balance side (uart_ota.c): downloads io-firmware.bin from Gitea to RAM,
computes SHA256, then streams to IO over UART1 (GPIO17/18, 460800 baud)
as OTA_BEGIN/OTA_DATA/OTA_END frames with CRC8 + per-chunk ACK/retry (×3).
IO side (uart_ota_recv.c): receives frames, writes to inactive OTA partition
via esp_ota_write, verifies SHA256 on OTA_END, sets boot partition, reboots.
IO board main.c + CMakeLists.txt scaffold included.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Downloads balance-firmware.bin from Gitea release URL to inactive OTA
partition, streams SHA256 verification via mbedTLS, sets boot partition
and reboots. Auto-rollback via CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE if
ota_self_health_check() not called within 30 s of boot. Progress 0-100%
in g_ota_self_progress for display task.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Adds gitea_ota_check_task on Balance board: fetches Gitea releases API
every 30 min and on boot, filters by esp32-balance/ and esp32-io/ tag
prefixes, compares semver against embedded FW version, stores update info
(version string, download URL, SHA256) in g_balance_update / g_io_update.
WiFi credentials read from NVS namespace "wifi"; falls back to compile-time
DEFAULT_WIFI_SSID/PASS if NVS is empty.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add dual OTA partitions (ota_0/ota_1 × 1.75 MB each) and otadata to
both esp32s3/balance/ and esp32s3/io/ on 4 MB flash layouts.
Enable CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE and OTA HTTP on Balance.
Create esp32s3/io/ project scaffold with config.h pin assignments.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replaces Orin↔ESP32-S3 BALANCE CAN comms (0x300-0x303 / 0x400-0x401)
with binary serial framing over CH343 USB-CDC at 460800 baud.
Protocol matches bd-wim1 (sl-perception) exactly:
Frame: [0xAA][LEN][TYPE][PAYLOAD][CRC8-SMBUS]
CRC covers LEN+TYPE+PAYLOAD, big-endian multi-byte fields.
Commands (Orin→ESP32): HEARTBEAT/DRIVE/ESTOP/ARM/PID
Telemetry (ESP32→Orin): TELEM_STATUS, TELEM_VESC_LEFT (ID 56),
TELEM_VESC_RIGHT (ID 68), ACK/NACK
VESC CAN TWAI kept for motor control; drive commands from Orin
forwarded to VESCs via SET_RPM. Hardware note: SN65HVD230
rewired from IO43/44 to IO2/IO1 to free IO43/44 for CH343.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
