Add hw_button driver (PC2 active-low, 20ms debounce) with gesture detection:
- Single short press + 500ms quiet -> BTN_EVENT_PARK
- SHORT+SHORT+LONG combo (within 3s) -> BTN_EVENT_REARM_COMBO
New BALANCE_PARKED state: PID frozen, motors off, quick re-arm via button
combo without the 3-second arm interlock required from DISARMED.
FC_BTN (0x404) CAN frame sent to Orin on each event:
event_id 1=PARKED, 2=UNPARKED, 3=UNPARK_FAILED (pitch > 20 deg)
Includes 11 unit tests (1016 assertions) exercising debounce, bounce
rejection, short/long classification, sequence detection, and timeout.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Issue #680 — IMU mount angle calibration:
- imu_cal_flash.h/.c: store pitch/roll offsets in flash sector 7
(0x0807FF00, 64 bytes; preserves PID records across sector erase)
- mpu6000_set_mount_offset(): subtracts offsets from pitch/roll output
- mpu6000_has_mount_offset(): reports cal_status=2 to Orin
- 'O' CDC command: capture current pitch/roll → save to flash → ACK JSON
- Load offsets on boot; report in printf log
CAN telemetry correction (Tee: production has no USB to Orin):
- FC_IMU (0x402): pitch/roll/yaw/cal_status/balance_state at 50 Hz
- orin_can_broadcast_imu() rate-limited to ORIN_IMU_TLM_HZ (50 Hz)
- FC_BARO (0x403): pressure_pa/temp_x10/alt_cm at 1 Hz (Issue #672)
- orin_can_broadcast_baro() rate-limited to ORIN_BARO_TLM_HZ (1 Hz)
Issue #685 — LED CAN override:
- ORIN_CAN_ID_LED_CMD (0x304): pattern/brightness/duration_ms from Orin
- orin_can_led_override volatile state + orin_can_led_updated flag
- main.c: apply pattern to LED state machine on each LED_CMD received
Orin side:
- saltybot_can_node.py: production SocketCAN bridge — reads 0x400-0x403,
publishes /saltybot/imu, /saltybot/balance_state, /saltybot/barometer;
subscribes /cmd_vel → 0x301 DRIVE; /saltybot/leds → 0x304 LED_CMD;
sends 0x300 HEARTBEAT at 5 Hz; sends 0x303 ESTOP on shutdown
- setup.py: register saltybot_can_node entry point + uart_bridge launch
Fix: re-apply --defsym __stack_end=_estack-0x1000 linker fix to branch
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- can_driver: add filter bank 15 (all ext IDs → FIFO1) and widen bank 14
to accept all standard IDs; add can_driver_send_ext/std and ext/std
frame callbacks (can_driver_set_ext_cb / can_driver_set_std_cb)
- vesc_can: VESC 29-bit extended CAN protocol driver — send RPM to IDs 56
and 68 (FSESC 6.7 Pro Mini Dual), parse STATUS/STATUS_4/STATUS_5
big-endian payloads, alive timeout, JLINK_TLM_VESC_STATE at 1 Hz
- orin_can: Orin↔FC standard CAN protocol — HEARTBEAT/DRIVE/MODE/ESTOP
commands in, FC_STATUS + FC_VESC broadcast at 10 Hz
- jlink: add JLINK_TLM_VESC_STATE (0x8E), jlink_tlm_vesc_state_t (22 bytes),
jlink_send_vesc_state_tlm()
- main: wire vesc_can_init/orin_can_init; replace can_driver_send_cmd with
vesc_can_send_rpm; inject Orin CAN speed/steer into balance PID; add
Orin CAN estop/clear handling; add orin_can_broadcast at 10 Hz
- test: 56-test host-side suite for vesc_can; test/stubs/stm32f7xx_hal.h
minimal HAL stub for all future host-side tests
Safety: balance PID runs independently on Mamba — if Orin CAN link drops
(orin_can_is_alive() == false) the robot continues balancing in-place.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
