sl-firmware
98494a98c7
gc9a01.c and gc9a01.h were never committed to main despite ota_display.c depending on their display_fill_rect/draw_string/draw_arc functions. Also: - CMakeLists.txt: add gc9a01.c to SRCS - config.h: restore DISP_* GPIO defs (DC=8 CS=9 SCK=10 MOSI=11 RST=14 BL=2) for Waveshare ESP32-S3-Touch-LCD-1.28 - ota_display.c: fix snprintf buffer too small (verline[32]→[48]) which GCC 13.2.0 rejects as -Werror=format-truncation Confirmed builds clean and boots on bd-66hx hardware (mbpi5 /dev/ttyACM0). Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
51 lines
2.2 KiB
C
51 lines
2.2 KiB
C
#pragma once
|
||
|
||
/* ── ESP32-S3 BALANCE board — bd-66hx pin/config definitions ───────────────
|
||
*
|
||
* Hardware change from pre-bd-66hx design:
|
||
* Previously: IO43/IO44 = CAN SN65HVD230 (shared Orin+VESC bus via CANable2)
|
||
* After bd-66hx: IO43/IO44 = CH343 UART0 (Orin serial comms)
|
||
* IO2/IO1 = CAN SN65HVD230 rewired (VESC-only bus)
|
||
*
|
||
* The SN65HVD230 transceiver physical wiring must be updated from IO43/44
|
||
* to IO2/IO1 when deploying this firmware. See docs/SAUL-TEE-SYSTEM-REFERENCE.md.
|
||
*/
|
||
|
||
/* ── Orin serial (CH343 USB-to-UART, 1a86:55d3 on Orin side) ── */
|
||
#define ORIN_UART_PORT UART_NUM_0
|
||
#define ORIN_UART_BAUD 460800
|
||
#define ORIN_UART_TX_GPIO 43 /* ESP32→CH343 RXD */
|
||
#define ORIN_UART_RX_GPIO 44 /* CH343 TXD→ESP32 */
|
||
#define ORIN_UART_RX_BUF 1024
|
||
#define ORIN_TX_QUEUE_DEPTH 16
|
||
|
||
/* ── VESC CAN TWAI (SN65HVD230 transceiver, rewired for bd-66hx) ── */
|
||
#define VESC_CAN_TX_GPIO 2 /* ESP32 TWAI TX → SN65HVD230 TXD */
|
||
#define VESC_CAN_RX_GPIO 1 /* SN65HVD230 RXD → ESP32 TWAI RX */
|
||
#define VESC_CAN_RX_QUEUE 32
|
||
|
||
/* VESC node IDs — matched to bd-wim1 TELEM_VESC_LEFT/RIGHT mapping */
|
||
#define VESC_ID_A 56u /* TELEM_VESC_LEFT (0x81) */
|
||
#define VESC_ID_B 68u /* TELEM_VESC_RIGHT (0x82) */
|
||
|
||
/* ── GC9A01 240×240 round display (Waveshare ESP32-S3-Touch-LCD-1.28) ── */
|
||
#define DISP_DC_GPIO 8
|
||
#define DISP_CS_GPIO 9
|
||
#define DISP_SCK_GPIO 10
|
||
#define DISP_MOSI_GPIO 11
|
||
#define DISP_RST_GPIO 14
|
||
#define DISP_BL_GPIO 2
|
||
|
||
/* ── Safety / timing ── */
|
||
#define HB_TIMEOUT_MS 500u /* heartbeat watchdog: disarm if exceeded */
|
||
#define DRIVE_TIMEOUT_MS 500u /* drive command staleness timeout */
|
||
#define TELEM_STATUS_PERIOD_MS 100u /* 10 Hz status telemetry to Orin */
|
||
#define TELEM_VESC_PERIOD_MS 100u /* 10 Hz VESC telemetry to Orin */
|
||
|
||
/* ── Drive → VESC RPM scaling ── */
|
||
#define RPM_PER_SPEED_UNIT 5 /* speed_units=1000 → 5000 ERPM */
|
||
#define RPM_PER_STEER_UNIT 3 /* steer differential scale */
|
||
|
||
/* ── Tilt cutoff ── */
|
||
#define TILT_CUTOFF_DEG 25.0f
|