sl-firmware
accf7fdf39
Protocol choice: implemented from spec (CRSFforArduino needs Arduino
framework; Betaflight extraction has deep scheduler dependencies).
Protocol verified against Betaflight src/main/rx/crsf.c + CRSF spec.
crsf.c:
- UART4 PA0=TX/PA1=RX (GPIO_AF8_UART4), 420000 baud 8N1, oversampling×8
APB1=54MHz → BRR=0x101 → 418604 baud (0.33% error, within spec)
- DMA1 Stream2 Channel4, circular 64-byte buffer, IDLE interrupt
DMA half/complete callbacks drain buffer; IDLE fires at frame boundary
- CRC8 DVB-S2 (polynomial 0xD5) validated on every frame
- Parser state machine: SYNC(0xC8)→LEN→DATA with length sanity check
- 11-bit channel unpack for all 16 channels from 22-byte payload
- RC channels frame (0x16): unpacks 16ch, updates last_rx_ms + armed
- Link stats frame (0x14): captures RSSI dBm, LQ%, SNR dB
crsf.h: added rssi_dbm, link_quality, snr fields to CRSFState
config.h: CRSF_ARM_THRESHOLD=1750, CRSF_STEER_MAX=400, CRSF_FAILSAFE_MS=300
main.c:
- crsf_init() called after motor_driver_init()
- RC failsafe: disarm if (now - last_rx_ms) > CRSF_FAILSAFE_MS, but only
after RC was first seen (last_rx_ms != 0) — USB-only mode unaffected
- RC arm: CH5 rising edge → safety_arm_start(); falling edge → disarm
Same ARMING_HOLD_MS interlock as USB arm command
- RC steer: CH1 → crsf_to_range() → ±CRSF_STEER_MAX → motor_driver steer
- RSSI/LQ: appended to JSON when safety_rc_alive() ("rssi","lq" fields)
ui/index.html: hidden RC RSSI row revealed on first packet with rssi/lq
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
157 lines
5.4 KiB
C
157 lines
5.4 KiB
C
#ifndef CONFIG_H
|
|
#define CONFIG_H
|
|
|
|
// ============================================
|
|
// SaltyLab Balance Bot — MAMBA F722S FC
|
|
// Pin assignments from Betaflight: DIAT-MAMBAF722_2022B
|
|
// ============================================
|
|
|
|
// --- IMU: MPU6000 (SPI1) ---
|
|
// SPI1: PA5=SCK, PA6=MISO, PA7=MOSI
|
|
// WHO_AM_I = 0x68
|
|
#define MPU_SPI SPI1
|
|
#define MPU_CS_PORT GPIOA
|
|
#define MPU_CS_PIN GPIO_PIN_4 // GYRO_CS 1
|
|
#define MPU_EXTI_PORT GPIOC
|
|
#define MPU_EXTI_PIN GPIO_PIN_4 // GYRO_EXTI 1 (data ready IRQ)
|
|
#define GYRO_ALIGN CW270 // gyro_1_sensor_align = CW270
|
|
|
|
// --- Barometer: BMP280 or DPS310 (I2C1) ---
|
|
#define BARO_I2C I2C1
|
|
#define BARO_SCL_PORT GPIOB
|
|
#define BARO_SCL_PIN GPIO_PIN_8 // I2C_SCL 1
|
|
#define BARO_SDA_PORT GPIOB
|
|
#define BARO_SDA_PIN GPIO_PIN_9 // I2C_SDA 1
|
|
// Magnetometer also on I2C1 (external, header only)
|
|
|
|
// --- LEDs ---
|
|
#define LED1_PORT GPIOC
|
|
#define LED1_PIN GPIO_PIN_15 // LED 1 (active low)
|
|
#define LED2_PORT GPIOC
|
|
#define LED2_PIN GPIO_PIN_14 // LED 2 (active low)
|
|
|
|
// --- Buzzer ---
|
|
#define BEEPER_PORT GPIOB
|
|
#define BEEPER_PIN GPIO_PIN_2 // BEEPER 1
|
|
#define BEEPER_INVERTED 1 // beeper_inversion = ON
|
|
// beeper_od = OFF (push-pull)
|
|
|
|
// --- Battery Monitoring (ADC3) ---
|
|
#define ADC_VBAT_PORT GPIOC
|
|
#define ADC_VBAT_PIN GPIO_PIN_1 // ADC_BATT 1
|
|
#define ADC_CURR_PORT GPIOC
|
|
#define ADC_CURR_PIN GPIO_PIN_3 // ADC_CURR 1
|
|
#define ADC_IBAT_SCALE 115 // ibata_scale
|
|
|
|
// --- LED Strip (WS2812) ---
|
|
#define LED_STRIP_PORT GPIOB
|
|
#define LED_STRIP_PIN GPIO_PIN_3 // LED_STRIP 1 (TIM2_CH2)
|
|
|
|
// --- OSD: MAX7456 (SPI2) ---
|
|
#define OSD_SPI SPI2
|
|
#define OSD_CS_PORT GPIOB
|
|
#define OSD_CS_PIN GPIO_PIN_12 // OSD_CS 1
|
|
// SPI2: PB13=SCK, PB14=MISO, PB15=MOSI
|
|
|
|
// --- Blackbox Flash: M25P16 (SPI3) ---
|
|
#define FLASH_SPI SPI3
|
|
#define FLASH_CS_PORT GPIOA
|
|
#define FLASH_CS_PIN GPIO_PIN_15 // FLASH_CS 1
|
|
// SPI3: PC10=SCK, PC11=MISO, PB5=MOSI
|
|
|
|
// --- Motor Outputs (PWM/DShot) ---
|
|
#define MOTOR1_PORT GPIOC
|
|
#define MOTOR1_PIN GPIO_PIN_8 // TIM8_CH3
|
|
#define MOTOR2_PORT GPIOC
|
|
#define MOTOR2_PIN GPIO_PIN_9 // TIM8_CH4
|
|
#define MOTOR3_PORT GPIOA
|
|
#define MOTOR3_PIN GPIO_PIN_8 // TIM1_CH1
|
|
#define MOTOR4_PORT GPIOA
|
|
#define MOTOR4_PIN GPIO_PIN_9 // TIM1_CH2
|
|
#define MOTOR5_PORT GPIOB
|
|
#define MOTOR5_PIN GPIO_PIN_0 // TIM3_CH3
|
|
#define MOTOR6_PORT GPIOB
|
|
#define MOTOR6_PIN GPIO_PIN_1 // TIM3_CH4
|
|
#define MOTOR7_PORT GPIOA
|
|
#define MOTOR7_PIN GPIO_PIN_10 // TIM1_CH3
|
|
#define MOTOR8_PORT GPIOB
|
|
#define MOTOR8_PIN GPIO_PIN_4 // TIM3_CH1
|
|
|
|
// --- UARTs ---
|
|
// USART1: PB6=TX, PB7=RX (serial 0, SmartAudio/VTX)
|
|
#define UART1_TX_PORT GPIOB
|
|
#define UART1_TX_PIN GPIO_PIN_6
|
|
#define UART1_RX_PORT GPIOB
|
|
#define UART1_RX_PIN GPIO_PIN_7
|
|
|
|
// USART2: PA2=TX, PA3=RX (serial 1)
|
|
#define UART2_TX_PORT GPIOA
|
|
#define UART2_TX_PIN GPIO_PIN_2
|
|
#define UART2_RX_PORT GPIOA
|
|
#define UART2_RX_PIN GPIO_PIN_3
|
|
|
|
// USART3: PB10=TX, PB11=RX (serial 2, SBUS RX default)
|
|
#define UART3_TX_PORT GPIOB
|
|
#define UART3_TX_PIN GPIO_PIN_10
|
|
#define UART3_RX_PORT GPIOB
|
|
#define UART3_RX_PIN GPIO_PIN_11
|
|
|
|
// UART4: PA0=TX, PA1=RX (serial 3)
|
|
#define UART4_TX_PORT GPIOA
|
|
#define UART4_TX_PIN GPIO_PIN_0
|
|
#define UART4_RX_PORT GPIOA
|
|
#define UART4_RX_PIN GPIO_PIN_1
|
|
|
|
// UART5: PC12=TX, PD2=RX (serial 4)
|
|
#define UART5_TX_PORT GPIOC
|
|
#define UART5_TX_PIN GPIO_PIN_12
|
|
#define UART5_RX_PORT GPIOD
|
|
#define UART5_RX_PIN GPIO_PIN_2
|
|
|
|
// USART6: PC6=TX, PC7=RX (serial 5)
|
|
#define UART6_TX_PORT GPIOC
|
|
#define UART6_TX_PIN GPIO_PIN_6
|
|
#define UART6_RX_PORT GPIOC
|
|
#define UART6_RX_PIN GPIO_PIN_7
|
|
|
|
// --- PINIO (switchable outputs, e.g. VTX power) ---
|
|
#define PINIO1_PORT GPIOC
|
|
#define PINIO1_PIN GPIO_PIN_2 // pinio_config = 129 (USER1)
|
|
#define PINIO2_PORT GPIOC
|
|
#define PINIO2_PIN GPIO_PIN_0 // pinio_config = 129 (USER2)
|
|
|
|
// --- SaltyLab Assignments ---
|
|
// Hoverboard ESC: USART2 (PA2=TX, PA3=RX) or USART3
|
|
// ELRS Receiver: UART4 (PA0=TX, PA1=RX) — CRSF 420000 baud
|
|
// Jetson: USART6 (PC6=TX, PC7=RX)
|
|
// Debug: UART5 (PC12=TX, PD2=RX)
|
|
|
|
// --- CRSF / ExpressLRS ---
|
|
// CH1[0]=steer CH2[1]=lean(future) CH5[4]=arm CH6[5]=mode
|
|
#define CRSF_ARM_THRESHOLD 1750 /* CH5 raw value; > threshold = armed */
|
|
#define CRSF_STEER_MAX 400 /* CH1 range: -400..+400 motor counts */
|
|
#define CRSF_FAILSAFE_MS 300 /* Disarm after this ms without a frame */
|
|
|
|
// --- PID Tuning ---
|
|
#define PID_KP 35.0f
|
|
#define PID_KI 1.0f
|
|
#define PID_KD 1.0f
|
|
#define PID_INTEGRAL_MAX 500.0f
|
|
#define PID_LOOP_HZ 1000
|
|
|
|
// --- Safety ---
|
|
#define MAX_TILT_DEG 25.0f
|
|
#define RC_TIMEOUT_MS 500
|
|
#define ARMING_HOLD_MS 3000
|
|
#define MAX_SPEED_LIMIT 100
|
|
#define WATCHDOG_TIMEOUT_MS 50
|
|
|
|
// --- Motor Driver ---
|
|
#define MOTOR_CMD_MAX 1000 /* ESC range: -1000..+1000 */
|
|
#define MOTOR_STEER_RAMP_RATE 20 /* counts/ms — steer ramp only */
|
|
|
|
// --- IMU Calibration ---
|
|
#define GYRO_CAL_SAMPLES 1000 /* gyro bias samples (~1s at 1ms/sample) */
|
|
|
|
#endif // CONFIG_H
|