sl-webui
f71dad5344
Architecture change (2026-04-03): Mamba F722S (STM32F722) and BlackPill replaced by ESP32 BALANCE (PID loop) and ESP32 IO (motors/sensors/comms). - Update CLAUDE.md, docs, chassis BOM/ASSEMBLY, pinout, power-budget, wiring-diagram, TEAM.md, AUTONOMOUS_ARMING.md, docker-compose - Update all ROS2 package comments, config labels, launch args (stm32_port→esp32_port, /dev/stm32-bridge→/dev/esp32-bridge) - Update WebUI: stm32Mode→esp32Mode, stm32Version→esp32Version, "STM32 State/Mode" labels → "ESP32 State/Mode" (ControlMode, SettingsPanel) - Add TODO(esp32-migration) markers on stm32_protocol.py and mamba_protocol.py binary frame layouts — pending ESP32 protocol spec from max - Fix roslib CDN 1.3.0→1.4.0 in all 11 HTML panels (fixes ROS2 Humble rosbridge "Received a message without an op" incompatibility) Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
84 lines
3.2 KiB
Python
84 lines
3.2 KiB
Python
"""
|
||
uart_bridge.launch.py — FC↔Orin UART bridge (Issue #362)
|
||
|
||
Launches serial_bridge_node configured for Jetson Orin UART port.
|
||
Bridges Flight Controller (ESP32) telemetry from /dev/ttyTHS1 into ROS2.
|
||
|
||
Published topics (same as USB CDC bridge):
|
||
/saltybot/imu sensor_msgs/Imu — pitch/roll/yaw as angular velocity
|
||
/saltybot/balance_state std_msgs/String (JSON) — full PID diagnostics
|
||
/diagnostics diagnostic_msgs/DiagnosticArray — system health
|
||
|
||
Usage:
|
||
ros2 launch saltybot_bridge uart_bridge.launch.py
|
||
|
||
# Override UART port (Orin has THS0–THS3):
|
||
ros2 launch saltybot_bridge uart_bridge.launch.py uart_port:=/dev/ttyTHS0
|
||
|
||
# Override baud rate:
|
||
ros2 launch saltybot_bridge uart_bridge.launch.py baud_rate:=115200
|
||
|
||
Prerequisites:
|
||
- Flight Controller connected to /dev/ttyTHS1 @ 921600 baud
|
||
- ESP32 BALANCE firmware transmitting JSON telemetry frames (50 Hz)
|
||
- ROS2 environment sourced (source install/setup.bash)
|
||
|
||
Note:
|
||
/dev/ttyTHS1 is the native UART1 on Jetson Orin. Verify connectivity:
|
||
$ cat /dev/ttyTHS1 | head -5
|
||
{"p":123,"r":-45,"e":0,"ig":0,"m":0,"s":1,"y":0}
|
||
...
|
||
|
||
Troubleshooting:
|
||
- "Permission denied" → run with sudo or add user to dialout group
|
||
- No frames received → check Flight Controller baud rate, verify UART cable
|
||
- Garbled output → check baud rate mismatch, check cable shield/termination
|
||
"""
|
||
|
||
from launch import LaunchDescription
|
||
from launch.actions import DeclareLaunchArgument
|
||
from launch.substitutions import LaunchConfiguration
|
||
from launch_ros.actions import Node
|
||
|
||
|
||
def generate_launch_description():
|
||
return LaunchDescription([
|
||
# ── Launch arguments ───────────────────────────────────────────────────
|
||
DeclareLaunchArgument(
|
||
"uart_port",
|
||
default_value="/dev/ttyTHS1",
|
||
description="Jetson Orin UART device (THS0–THS3)",
|
||
),
|
||
DeclareLaunchArgument(
|
||
"baud_rate",
|
||
default_value="921600",
|
||
description="Serial baud rate (Flight Controller standard)",
|
||
),
|
||
DeclareLaunchArgument(
|
||
"timeout",
|
||
default_value="0.1",
|
||
description="Serial read timeout in seconds",
|
||
),
|
||
DeclareLaunchArgument(
|
||
"reconnect_delay",
|
||
default_value="2.0",
|
||
description="Delay before reconnect attempt on serial error (seconds)",
|
||
),
|
||
|
||
# ── Serial bridge node ─────────────────────────────────────────────────
|
||
Node(
|
||
package="saltybot_bridge",
|
||
executable="serial_bridge_node",
|
||
name="fc_uart_bridge",
|
||
output="screen",
|
||
parameters=[
|
||
{
|
||
"serial_port": LaunchConfiguration("uart_port"),
|
||
"baud_rate": LaunchConfiguration("baud_rate"),
|
||
"timeout": LaunchConfiguration("timeout"),
|
||
"reconnect_delay": LaunchConfiguration("reconnect_delay"),
|
||
},
|
||
],
|
||
),
|
||
])
|